郭寧

教育經歷：

2007/09 - 2012/06，重慶大學，材料科學與工程學院，博士；

2003/09 - 2007/06，重慶大學，材料科學與工程學院，學士；

工作經歷：

2017/07– 2018/07，Queen’s University，機械與材料工程系，訪問學者；

2012/12– 2015/12，重慶大學冶金工程博士后流動站，博士后；

2012/07 – 2018.06，西南大學材料與能源學部，講師；

2018/07–至今，西南大學材料與能源學部，副教授。

1. 梯度材料（可控制備、形變協調、退火行為及強韌化機理）

2. 鋼鐵材料（表面改性、組織表徵、力學行為）

3. 複合材料（可控制備、組織表徵、形變機理及力學行為等）

主持項目：

Ø 國家自然科學基金青年基金(51501158)

Ø 國家公派留學面上項目（201706995008）

Ø 重慶市博士后特別資助（XM201329）

Ø 中央高校基本科研業務費一般項目(XDJK2013C088、XDJK2015C063)

Ø 西南大學博士基金（SWU112043）

Ø 電子束表面改性40Cr鋼組織表徵及性能研究等橫向課題三項

（1）論文：

Jianjun Hu, Jie Jiang, Hui Li, Xian Yang, Hongbin Xu*, Yan Jin, Chaoping Ma, Qingshan Dong, Ning Guo*, Effect of Annealing Treatment on Microstructure and Properties of Cr-Coatings Deposited on AISI 5140Steel by Brush-Plating, Coatings, 8, 193, doi:10.3390/coatings8050193，2018

J. Hu, Y. Zhang, X. Yang, H. Li, H. Xu*, C. Ma, Q. Dong, N. Guo*, Z. Yao, Effect of pack-chromizing temperature on microstructure and performance of AISI 5140 steel with Cr-coatings. Surface and Coatings Technology, 344:656-663, 2018.

Ning Guo*, Zhimin Zhang, Qingshan Dong, Hongbing Yu, Bo Song, Linjiang Chai, Cong Liu,Zhongwen Yao, Mark R. Daymond. Strengthening and toughening austenitic steel by introducing gradient martensite via cyclic forward/reverse torsion. Materials and Design, 143:150–159, 2018.

Hongbin Xu, Jianjun Hu*, Chaoping Ma, Linjiang Chai and Ning Guo*. Influence of Electron Beam Irradiation on Surface Roughness of Commercially AISI 5140 Steel. Materials Transactions, 58(11): 1519-1523, 2017.

Jianjun Hu, Chaoping Ma, Xian Yang, Hongbin Xu*, Ning Guo*, Hongbing Yu. Microstructure evolution during continuous cooling in AISI 5140 steel processed by induction heating chromizing. Journal of Materials Engineering and Performance, 26: 5530-5537, 2017.

Ning Guo*, Bo Song*, Hongbing Yu, Renlong Xin, Bingshu Wang, Tingting Liu. Enhancing tensile strength of Cu by introducing gradient microstructures via a simple torsion deformation. Materials & Design, 90:545-550, 2016.

Bo Song, Ning Guo*, Renlong Xin*, Hucheng Pan, Changfa Guo. Strengthening and toughening of extruded magnesium alloy rods by combining pre-torsion deformation with subsequent annealing. Materials Science and Engineering A, 650:300-304, 2016.

Ning Guo*, Dongrong Li, Hongbing Yu, Renlong Xin, Zhimin Zhang, Xiaoxia Li, Cong Liu, Bo Song*, Linjiang Chai*. Annealing behavior of gradient structured copper and its effect on mechanical properties.Materials Science and Engineering A, 702, 331–342, 2017.

Bo Song*, Hucheng Pan, Linjiang Chai, Ning Guo*, Huaizhi Zhao, Renlong Xin*. Evolution of gradient microstructure in an extruded AZ31 rod during torsion and annealing and its effects on mechanical properties. Materials Science and Engineering A, 689 (24), 78–88, 2017.

Bo Song*, Xiaogang Shu, Hucheng Pan, Guoqiang Li,Ning Guo*,Tingting Liu, Linjiang Chai, Renlong Xin*. Influence of Torsion Route on the Microstructure and Mechanical Properties of Extruded AZ31 Rods.Advanced Engineering Materials, 19(11):1527-2648, 2017.

LinJiang Chai*,ShuYan Wang,Hao Wu,ZhiNan Yang,HuCheng Pan,Bo Song,Ning Guo*. Bimodal plate structures induced by pulsed laser in duplex-phase Zr alloy. ScienceChinaTechnological Sciences, 60(4), 587–592, 2017.

Ning Guo*, Xiaoxia Li, Mei Xiao, Renlong Xin, Linjiang Chai, Bo Song*, Hongbing Yu, Lu Li. Microstructures and mechanical properties of commercial hot-extruded copper processed by torsion deformation. Advanced Engineering Materials, 18(10),1738-1746, 2016.

[Bo Song*, Huaizhi Zhao, Linjiang Chai, Ning Guo*, Hucheng Pan, Hongbing Chen and Renlong Xin*. Preparation and Characterization of Mg Alloy Rods with Gradient Microstructure by Torsion Deformation. Metals and Materials International，22(5), 887-896, 2016.

Ning Guo*, Bo Song*, Hongbing Yu, Renlong Xin, Bingshu Wang, Tingting Liu. Enhancing tensile strength of Cu by introducing gradient microstructures via a simple torsion deformation. Materials & Design, 90:545-550, 2016.

Bo Song, Ning Guo*, Renlong Xin*, Hucheng Pan, Changfa Guo. Strengthening and toughening of extruded magnesium alloy rods by combining pre-torsion deformation with subsequent annealing. Materials Science and Engineering A, 650:300-304, 2016.

Ning Guo, Bo Song*, Changfa Guo, Renlong Xin, Qing Liu. Improving tensile and compressive properties of extruded magnesium alloys via a simple pre-torsion deformation. Materials & Design, 83:270-275, 2015.

Bingshu Wang, Liping Deng, Chapuis Adrien, Ning Guo, Zeren Xu, Qiang Li. Relationship between textures and deformation modes in Mg–3Al–1Zn alloy during uniaxial tension. Materials Characterization, 108, 42–50, 2015.

Song B, Xin RL, Guo N, Xu JB, Sun LY, Liu Q. Dependence of tensile and compressive deformation behavior on aging precipitation in rolled ZK60 alloys. Materials Science and Engineering A, 639:724-731, 2015.

Ning Guo, Bo Song, Bingshu Wang, Qing Liu. Influence of torsion deformation on textures of cold drawing pearlitic steel wires. ActaMetallurgica Sinica (English Letters), 28 (6): 707-714, 2015.

Chunmei Li, Nanpu Cheng, Zhiqian Chen, Ning Guo, Sumin Zeng. Deep-cryogenic- treatment-induced phase transformation in the Al-Zn-Mg-Cu alloy，International Journal of Minerals Metallurgy and Materials，22（1）：68-77, 2015.

Bingshu Wang, Liping Deng, Ning Guo, Zeren Xu, Qiang Li. EBSD analysis of {10–12} twinning activity in Mg–3Al–1Zn alloy during compression. Materials Characterization 98, 180-185, 2014.

Ning Guo, Baifeng Luan, Zhiqiang Li, Genlian Fan, Di Zhang, Qing Liu. Microstructure and strength of Al2O3/Al composites fabricated by flake powder metallurgy. New Frontiers of Nanoemtals, Edited by S. Faester, N. Hansen, D. Juul Jensen, B. Ralph and J. Sun, 283-292, 2014 (35th Risø International Symposium on Materials Science).

Bo Song, Ning Guo, Tingting Liu, QingShan Yang. Improvement of formability and mechanical properties of magnesium alloys via pre-twinning: A review. Materials & Design, 62, 352–360, 2014.

Ning Guo, Baifeng Luan, Fangfang He, Zhiqiang Li and Qing Liu. Influence of flake thickness on the shape and distribution of Al2O3 particles in Al-matrix composites fabricated by flake powder metallurgy. Scripta Materialia, 78-79, 1-4, 2014.

Ning Guo, Tingting Liu, Baifeng Luan, Bingshu Wang and Qing Liu. Dislocation density and configuration in fully pearlitic steel during wire drawing. Materials Research Innovations, 18, s249-254, 2014.

Guo Ning, Song Bo, Luan Baifeng, Chen Zhiqian and Liu Qing. Deformation bands in fully pearlitic steel during wire drawing. ScienceChina Technological Sciences, 57(4) 796-803, 2014

Ning Guo, Baifeng Luan, Qing Liu. Influence of pre-torsion deformation on microstructures and properties of cold drawing pearlitic steel wires. Materials & Design, 50, 285-292, 2013.

Guo Ning, Luan Baifeng, Wang Bingshu and Liu Qing. Microstructure and texture evolution in fully pearlitic steel during wire drawing. Science ChinaTechnological Sciences, 56 1139-1146, 2013.

N. GUO and Q. LIU. Back-scattered electron imaging combined with EBSD technique for characterization of pearlitic steels. Journal of Microscopy, 246(3), 221-228, 2012.

GUO Ning, LIU Qing, Xin Yunchang, et al. The application of back-scattered electron imaging for characterization of pearlitic steels. ScienceChina Technological Sciences, 54(9), 2368-2372, 2011.

1.

Ning Guo*

2.

N. Guo*

3.

Ning Guo

4.

*

5.

Ning Guo*

6.

Ning Guo*

7.

Ning Guo*

8.

Ning Guo*

9.

*

10.

*

11.

Ning Guo*

12.

Ning Guo*

13.

Ning Guo*

14.

Ning Guo*

15.

Ning Guo*

16.

Ning Guo,

17.

Ning Guo

18.

Guo N

19.

Ning Guo

20.

Ning Guo

21.

Ning Guo

22.

Ning Guo

23.

Ning Guo

24.

Ning Guo

25.

Ning Guo

26.

Guo Ning

27.

Ning Guo

28.

Guo Ning

29.

N. GUO

30.

GUO Ning

.